E. coli in Surface WatersContact: Molly Rippke 517-342-4419
Note: this page can be accessed as www.mi.gov/egleecoli
- What is E. coli?
- How does E. coli get into surface water?
- How much E. coli is too much?
- How is E. coli measured?
- What resources are available to help me sample my waterbody?
- Where can I find E. coli data?
- What does EGLE do if we find a problem?
Escherichia coli (E. coli) is a type of bacteria (single cell organism) that is used by the State of Michigan as a water quality indicator. When E. coli is found in surface waters, it means that there has been fecal contamination. While E. coli itself may be harmful to human health, other disease causing organisms might also be present. Once these pathogens are in a stream or lake, they can infect humans through ingestion or skin contact, resulting in diseases such as gastroenteritis (diarrhea), giardia, hepatitis, or cholera.
Common and potential sources of E. coli contamination vary by where you are in the landscape. For example, urban areas would be expected to have a different set of sources than a rural farm-type setting where there are livestock and people rely on septic systems. All animals (livestock, pets and wildlife) and human sewage are possible sources under certain circumstances. For more details on sources and how EGLE works to prevent them from entering surface water, see Michigan’s Statewide E. coli TMDL.
To find out how you can help reduce E. coli contamination of our rivers, lakes, and beaches, please see our Guide for Homeowners.
The Water Quality Standard for E. coli was developed to protect human health during work and play, and is the maximum amount of E. coli that is allowable in surface waters of the state. These standards, known as the total and partial body contact (or recreation) standards, apply to all waters of the state, including streams, rivers, wetlands, lakes and beaches. The geometric mean of three samples at the site (collected on the same date) are needed to compare to the standard as described by Rule 62 of the Part 4 Water Quality Standards. The water quality standard is more conservative during the summer to protect swimmers during total body contact, but water is protected all year round by the partial body contact standard. For a 30-day geometric mean calculation, five weekly sampling events are needed, within a 30 day period.
Water Quality Standard for E. coli:
Total Body Contact (May 1 - October 31):
Daily Maximum Geometric Mean: 300 E. coli per 100 milliliters (ml)
30-Day Geometric Mean: 130 E. coli per 100 ml
Partial Body Contact (all year):
Daily Maximum Geometric Mean: 1,000 E. coli per 100 ml
E. coli in water exists in colonies that can be suspended in the water, or settle out with gravity. E. coli water samples should be collected in a manner that does not disturb the bottom sediment, and avoids capturing surface films or scums. Sterile containers and gloved hands are used to minimize sample contamination. Samples are collected from three locations (generally called ‘left”, “center” and “right”) at each site of interest, such as a road crossing of a river or a bathing beach. Samples should be taken to a laboratory within 6 hours, to prevent regrowth or death of the bacteria. Once at the lab, the personnel will count the colonies using one of several methods and report the results in colonies per volume of water. Then, a geometric mean of these three samples is calculated to compare with the water quality standard. For a 30-day geometric mean calculation, five weekly sampling events are needed, within a 30 day period.
- For Sampling Suggestions contact Molly Rippke.
- List of Certified Drinking Water Laboratories for bacteria (Note: Certification is not required to analyze E. coli in surface water, and drinking water methods differ from environmental methods. This link is provided as a resource.)
- EPA Approved Analytical Methods for Bacteria
- Your local health department may be able to analyze for E. coli. Find your local health department using the Michigan Department of Community Health website.
- The E. coli TMDL Pollution and Solution interactive mapper allows you to look for existing E. coli data near you. Please see the “Help” tab on the map or the help document before you get started.
- Annual Bacterial Monitoring Reports
- 2019 Annual Bacterial Monitoring Report
- 2018 Annual Bacterial Monitoring Report
- 2017 Annual Bacterial Monitoring Report
- Cass River E. coli Monitoring Report
- 2016 Annual Bacterial Monitoring Report
- 2015 Annual Bacterial Monitoring Report
- 2014 Annual Bacterial Monitoring Report
- BeachGuard is another mapping and text search interface designed to share beach closing and E. coli information collected by local health departments. BeachGuard also contains some E. coli results collected from rivers.
- Your local health department is also a good source for information. Use the “Contact Your Local Health Department” map on the Michigan Department of Health and Human Services website.
When the water quality standard is exceeded at a beach, lake or stream, EGLE goes through a process that is defined by the Federal Clean Water Act Section 303(d). Simply put, the state must make a list of all waters that are not meeting the standards or designated uses, then must address the issue in a document called a Total Maximum Daily Load. The state of Michigan estimates that roughly half of its rivers and streams exceed the Total Body Contact E. coli standard. Dozens of TMDLs have been U.S. EPA approved to address E. coli issues at beaches and on rivers, lakes and streams in Michigan (click here for a Map of Approved Michigan E. coli TMDLs). However, a TMDL itself does not make water clean, it is only a step in a long process which requires cooperation and efforts of multiple agencies (state and local) and public participation to be successful.